基于纸喷雾离子化衍生质谱法快速检测PM2.5中的醌污染物

醌类化合物是PM2.5中的一类有害物质。本研究建立了纸喷雾离子化衍生质谱法快速测定PM2.5中的醌类污染物。通过衍生化反应在醌化合物中引入氨基，提高醌在纸喷雾中的离子化效率。随后对衍生化试剂种类、电压、喷雾溶剂种类等反应条件进行优化。在最优实验条件下，采用内标法定量分析1,4-苯醌、甲基对苯醌、1,4-萘醌和1,4-蒽醌，4种化合物均呈现较好的线性关系，其检出限分别为4.49、20.89、0.13、0.17 ng。利用该方法分析PM2.5实际样品中的萘醌和蒽醌，均获得了较好的定性和定量结果。     

Stabilization of natural gas foams using different surfactants at high pressure and high temperature conditions

Natural gas foam can be used for mobility control and channel blocking during natural gas injection for enhanced oil recovery, in which stable foams need to be used at high reservoir temperature, high pressure and high water salinity conditions in field applications. In this study, the performance of methane (CH₄) foams stabilized by different types of surfactants was tested using a high pressure and high temperature foam meter for surfactant screening and selection, including anionic surfactant (sodium dodecyl sulfate), non-anionic surfactant (alkyl polyglycoside), zwitterionic surfactant (dodecyl dimethyl betaine) and cationic surfactant (dodecyl trimethyl ammonium chloride), and the results show that CH₄-SDS foam has much better performance than that of the other three surfactants. The influences of gas types (CH₄, N₂, and CO₂), surfactant concentration, temperature (up to 110°C), pressure (up to 12.0 MPa), and the presence of polymers as foam stabilizer on foam performance was also evaluated using SDS surfactant. The experimental results show that the stability of CH₄ foam is better than that of CO₂ foam, while N₂ foam is the most stable, and CO₂ foam has the largest foam volume, which can be attributed to the strong interactions between CO₂ molecules with H₂O. The foaming ability and foam stability increase with the increase of the SDS concentration up to 1.0 wt% (0.035 mol/L), but a further increase of the surfactant concentration has a negative effect. The high temperature can greatly reduce the stability of CH₄-SDS foam, while the foaming ability and foam stability can be significantly enhanced at high pressure. The addition of a small amount of polyacrylamide as a foam stabilizer can significantly increase the viscosity of the bulk solution and improve the foam stability, and the higher the molecular weight of the polymer, the higher viscosity of the foam liquid film, the better foam performance.     

A fuzzy logic PI control with feedforward compensation for hydrogen pressure in vehicular fuel cell system

In a vehicular fuel cell system, alternative load and frequent purge action can lead to anode pressure varies with the hydrogen mass flow fluctuation. It's crucial to control the pressure difference between anode and cathode within a reasonable range to avoid adverse phenomena such as membrane failure, reactant starvation, or even water management fault. In this paper, an improved proportional integrative (PI) controller by the fuzzy logic technique that considers the engineer experience and knowledge on the hydrogen supply system behavior is proposed for hydrogen pressure control, in which the PI parameters are tuned by a fuzzy decision process. Furthermore, load current and purge action regarded as input disturbances are applied for feedforward compensation to reduce the pressure response hysteresis. A hydrogen supply subsystem based on the proportional valve is modeled, and corresponding parameters are determined by analyzing the response time and steady pressure fluctuation. The performance of the conventional PI controller, the fuzzy logic PI (FLPI) controller and fuzzy logic PI with feedforward (FLPIF) controller is validated. The presented results indicated that the FLPI controller significantly improves the dynamic response of hydrogen pressure compared to the PI controller, and the FLPIF controller can further reduce overshoot caused by disturbance. Finally, the proposed FLPIF controller is implemented on a rapid prototype platform of the hydrogen supply subsystem and an actual fuel cell system, exhibiting satisfactory performance.     

上升气泡内气溶胶沉降机理研究

气溶胶池洗过滤是反应堆严重事故中去除放射性源项的重要手段。本文以严重事故条件下上升气泡中气溶胶的滞留过程为背景，设计搭建了可视化单气泡鼓泡实验装置。通过该装置研究了气溶胶在上升气泡中的沉降效率，并与MELCOR中的气溶胶沉降模型计算结果进行了对比。结果表明，气溶胶沉降效率对气泡尺寸的变化较为敏感，当气体流量大于0.1 L/min时，气泡等效直径迅速增加，相应的气溶胶沉降效率快速降低；与MELCOR模型计算结果的对比表明，两者在总体趋势上呈现出较好的一致性，但计算结果低估了液相对气溶胶的实际去除能力，导致这种偏差的主要原因是气泡在上升过程中存在无规则的晃动以及气液界面的波动。     

LoRa与NB-IoT通信技术研究现状

随着第4次工业革命的到来,物联网技术迅速发展,物联网设备的数量以指数形式增加.无线通信技术作为物联网技术的重要支撑,对其发展至关重要.作为LPWAN中应用最为广泛的两种无线通信技术,LoRa和NB-IoT具有低功耗、广覆盖、广连接等特点.文章对LoRa和NB-IoT无线通信技术进行了综述.首先,从成本、覆盖范围、容量、延迟、电池寿命、服务质量、可靠性等方面对LoRa和NB-IoT进行了对比;其次,总结了近年来这两种无线通信技术的研究现状及其应用场景;最后,对LoRa和NB-IoT今后研究方向进行了展望.     

基于K-AP算法的高光谱图像波段选择方法

在高光谱图像分析领域中，波段选择是一种能有效减少高光谱图像维度的方法。K类仿射传播算法是一种高效的聚类算法，已成功地应用于人脸识别和数据分析等领域，但在高光谱图像分析领域还少有成功的应用。提出将K-AP算法应用于高光谱图像波段选择，对高光谱图像进行有效的数据压缩。针对K-AP算法的特点，基于Kullback-Leibler散度定义了新的相似度矩阵，对波段进行度量，再使用K-AP算法进行聚类，选择最有代表性的波段。实验结果表明，与常用的波段选择方法相比，所提出的方法有更好的表现。     

基于张量分解融合RGB-D图像的物体识别

为了充分利用RGB-D图像的深度图像信息，提出了基于张量分解的物体识别方法。首先将RGB-D图像构造成一个四阶张量，然后将该四阶张量分解为一个核心张量和四个因子矩阵，再利用相应的因子矩阵将原张量进行投影，获得融合后的RGB-D数据，最后输入到卷积神经网络中进行识别。RGB-D数据集中三组相似物体的识别结果表明，利用张量分解融合RGB-D图像的物体识别准确率高于未采用张量分解的物体识别准确率，并且单一错分实例的准确率最高可提升99%。     

高性能三水醋酸钠-尿素-膨胀石墨混合相变材料的制备及其在电地暖中的应用性能

采用尿素调节三水醋酸钠的相变温度到合适范围再添加膨胀石墨来降低过冷度，研制了高性能的三水醋酸钠-尿素-膨胀石墨混合相变材料，并对其在电地暖中的应用性能进行了研究。结果表明，当尿素质量分数为36.5%、膨胀石墨添加量为4%(质量)时，所得混合相变材料的熔化焓高达209.1 J/g，熔点在31.98℃，过冷度仅为2.04℃，热导率为2.349 W/(m·K)，热可靠性良好；将用该混合相变材料制成的相变板安装在实验房的电地暖中时，实验房的热舒适度随着相变材料层厚度的增加而增加，但也带来加热时间和用电量的增加；当相变材料层厚度为10 mm时，电加热温度适宜设置在45℃；在热舒适度相当的条件下，有相变板的实验房与无相变板的参比房相比具有用电量小及电费低的优势。     

海洋工程和船舶焊接变形预测方法研究

目前,影响海洋工程和船舶焊接结构质量的重要影响因素之一就是焊接变形,其产生的根本原因就是在焊接过程中因结构体受热不均、热梯度、残余应力等。基于此,本文对焊接变形预测的理论发展进程及其相关理论内涵进行详细阐述,并对基于神经网络的新型焊接变形预测理论的研究发展简单概述。     

混料含水率对电解锰渣免烧砖性能的影响

以电解锰渣、水泥、骨料和水为主要原料制备电解锰渣免烧砖,在成型压力为10 MPa,水泥、骨料添加量分别为23％和25％的条件下,研究混料含水率对电解锰渣免烧砖各项性能的影响.结果 表明:混料含水率从20％增加至40％时,电解锰渣免烧砖抗压、抗折强度均先增大后减小,体积密度基本保持不变,线收缩率先减小后增大最后趋于稳定,吸水率和饱和系数总体先减小后增大.最适宜混料含水率为30％,此时砖样抗压、抗折强度均满足国家免烧砖MU10标准规定,其他性能参数均符合国家免烧砖一等品要求.